1 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com 1.877.LED.GLOW • LEDGLOW.COM BLUETOOTH MILLION COLOR GOLF CART LIGHTING KIT INSTALLATION GUIDE
2 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com
3 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com : Please check your state and local laws before installing this LED lighting kit. Every state has different policies and procedures in place regarding aftermarket vehicle accessories. LEDGlow is not responsible for any fines that you may receive while using this lighting kit. This kit is for off-road use only. Note: We recommend using a licensed professional to install this lighting kit. The improper installation of this kit will void all warranties. PLEASE READ THE FOLLOWING INSTRUCTIONS Thoroughly BEFORE INSTALLING AND OPERATING THIS LED GOLF CART KIT. • 4 SEATER GOLF CART BASE KIT INCLUDES:: • (2) 18” Flexible Tubes • (2) 28” Flexible Tubes • Control Box • Underbody Junction Box • Self-Tapping Screws • Zip Ties • 6 SEATER GOLF CART BASE KIT INCLUDES: • (2) 18” Flexible Tubes • (2) 46” Flexible Tubes • Control Box • Underbody Junction Box • Self-Tapping Screws • Zip Ties • OPTIONAL 4 SEATER GOLF CART ADD ON ACCESSORIES: • (4) 8” Flexible Interior Tubes • (4) 12” Flexible Wheel Well Tubes • (2) 36” Flexible Canopy Tubes & (2) 8” Flexible Interior Tubes • OPTIONAL 6 SEATER GOLF CART ADD ON ACCESSORIES: • (4) 36” Flexible Canopy Tubes • (4) 12” Flexible Wheel Well Tubes 1. Temporarily power the kit to ensure proper functionality of this kit before installation. Connect the red wire to the main positive (+) terminal and the black wire to the main negative (-) terminal on the 12-volt power source. 2. Arrange the tubes out on the ground the way you plan on installing them and connect them to the junction box. After powering the kit and determining it is functioning properly, remove the kit from power. 3. Disconnect the negative side of the golf cart’s battery. : Raise and support the golf cart if necessary.
4 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com 4. Clean the proposed mounting surfaces with an alcohol prep pad. The mounting surface should be between 45 and 85 degrees Fahrenheit to achieve the strongest bonding results from the double-sided adhesive tape. : The surface area must be free of all oils, moisture, dirt and wax for the supplied adhesive tape to bond and adhere to the installation surface properly. : To achieve the strongest bond between the tape on the lighting tubes and the golf cart, you can use Adhesion Promoter, which is sold separately from your kit at www.LEDGlow.com. Once the lighting tubes are in place make sure they are permanently secured using screws and/or zip ties. 5. When installing the underbody or wheel well lighting strips, ensure plenty of clearance from direct heat sources and moving parts. The lighting strips are flexible and can be contoured. UNDERBODY 6. Mount the front tube with the wire facing the driver’s side of the cart. 7. Mount the side tubes with the wires facing the front of the cart. 8. Mount the rear tube with the wire facing the passenger side of the cart. WHEEL WELL 9. Mount one of the wheel well tubes to the underside of the body in the wheel well area shining down onto the tire with the wire facing the front of the cart. 10. Repeat step #9 for the remaining wheel well tubes.
5 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com INTERIOR 11. Mount the interior tubes and secure with the wires facing either side of the cart. These lighting strips are generally mounted in the glove box area, under the dashboard under the backrest of the seat or in the cargo area (if applicable). CANOPY 12. Mount both canopy tubes to the underside of the canopy with the wires facing the rear of the cart. If you are using the self-tapping screws and mounting tabs for installation, ensure the screws are not too long to go through the canopy.Route the canopy tube wires down the rear canopy frame and under the seat. Be sure to secure the wires with zip ties. 13. Mount the junction box under the seat of the golf cart in a dry location. 14. Starting with the rear tube, run the wires to the junction box. Make sure to secure the wires tightly when going around any suspension parts using the included zip-ties.
6 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com If a wire is pinched, the kit may malfunction and could void the warranty. Run the underbody wires along the golf cart frame as well as the wheel well and interior wires and make sure everything is tightly secured. Ensure that all connections are secure. 15. Mount the control box under the seat or in the glove box of the golf cart making sure it is kept dry using the included adhesive tape. : The junction and control boxes MUST be mounted away from heat, moisture, and the elements. 16. Run the connection cable from the junction box to the control box and ensure that the connectors are secure. Interior/ Canopy Underbody Wheel Well Display
7 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com CONNECTING POWER TO ELECTRIC GOLF CARTS This Million Color Golf Cart Lighting Kit was designed to be powered by a 12 volt system. If you are running a 36 or 72 volt system, a Golf Cart Battery Voltage Reducer is required. This Reducer can be purchased at LEDGlow.com. The steps below will guide you through the process of installing your Million Color LED Golf Cart Underbody Lighting Kit using an LEDGlow Golf Cart Battery Voltage Reducer. 36 VOLT CONFIGURATION 6V 6V 6V 6V 6V 6V 36.0 Figure A 72 VOLT CONFIGURATION 12V 12V 12V 12V 12V 12V 72.0 Figure E 12V 12V 12V 12V 48 VOLT CONFIGURATION 48.0 Figure C 8V 8V 8V 8V 8V 8V 48 VOLT CONFIGURATION 48.0 Figure B 48 VOLT CONFIGURATION 48.0 Figure D 48V LITHIUM 72 VOLT CONFIGURATION 72.0 Figure F 72V LITHIUM 1. If you are unsure of the voltage in your golf cart, temporarily reconnect the negative side of the battery and verify voltage with a multimeter before connecting the kit to the golf cart. 2. The LEDGLow Golf Cart Battery Voltage Reducer can accept an input voltage of 1572 volts, while outputting 12 volts at a max of 5 amps. This allows you to connect to a power source on the cart safely. This also allows the light kit to draw power evenly from all of the batteries, prolonging the battery life of all batteries on the cart. 3. Switch your golf cart to TOW mode (if available) and turn the key switch to OFF so the golf cart is powered down.
8 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com 4. Because an electric golf cart requires significant current for standard operation, several batteries are typically wired in series in order to achieve the power needed. It is extremely important to test the voltage of the chosen power source prior to installing the Golf Cart Battery Voltage Reducer as failure to install it correctly could lead to overheating and complete failure of the voltage reducer. This could also potentially damage components of the golf cart and/or light kit. • A 36 volt golf cart will typically have (6) 6 volt batteries but are not limited to just that configuration. (Figure A) • A 48 volt golf cart could be wired in several different configurations but are not limited to: o (6) 8 volt batteries. (Figure B) o (4) 12 volt batteries. (Figure C) o (1) 48 volt lithium battery. (Figure D) • A 72 volt golf cart could be wired in several different configurations but are not limited to: o (6) 12 volt batteries. (Figure E) o (1) 72 volt lithium battery. (Figure F) 5. Using a multimeter set to Volts DC, test each individual battery’s voltage. To do this, hold one lead from the multimeter to the negative post of the main battery. Then, hold the other lead from the multimeter to the positive post of each battery, taking note of the voltage displayed on the multimeter at each battery. The controller will be connected to both the main positive and negative battery posts where voltage is the greatest. This will ensure an even draw of power across all batteries. For most lithium battery configurations, you connect to the positive and the negative posts. Note: Keep in mind that if a Golf Cart is retrofitted to have lithium batteries it is very possible that it will have multiple lower voltage batteries wired in series in order to add up to the correct voltage. If a Golf Cart has more than one higher voltage lithium battery, it is wired in parallel and this is used to extend the range of use by adding the amperage of the batteries together to have them operate longer. 6. Disconnect the main negative terminal of the golf cart’s battery. 7. Find a good, flat metal surface to mount the Golf Cart Battery Voltage Reducer using screws and double-sided tape, away from any heat or moving parts. The Golf Cart Battery Voltage Reducer may reach high temperatures, so it is important that this is not installed in direct contact with any plastic parts of the golf cart. 8. Connect the Yellow Wire from the Input of the Reducer to the main positive terminal of the battery(s) on the golf cart using the eyelet connector. 9. Connect the Green Wire from the Input of the Reducer to the main negative terminal of the battery(s) on the golf cart using the eyelet connector. 10. Connect the Red Wire from the Output of the Reducer to the positive wire of the lighting accessory that you are installing to the golf cart using the crimp on butt connector. 11. Connect the Black Wire from the Output of the Reducer to the ground wire of the lighting accessory that you are installing to the golf cart using the crimp on butt connector.
9 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com 12. Reconnect the main negative terminal of the golf cart’s battery and switch your cart back to RUN mode (if available). CONNECTING POWER TO GAS ENGINE CARTS 1. Connect the red wire from the control box to a positive 12-volt source. If you are unsure of available voltage in your golf cart, verify voltage with a multimeter before connecting the kit to the golf cart. Note: If you need to extend the power wires, be sure to use 16- or 18-gauge automotive grade wire. If you are running the power wire to the battery and must go through metal, use an existing grommet or drill a hole and add a new grommet, which are available at any auto parts store. Be sure to reinstall the fuse within 6” of the power source. If you connect the power wire to a switched 12-volt source, then it will not remember the previous color and pattern to which is it was last set. 2. Connect the black wire from the control box to a good ground source, grounding block, or directly to the negative terminal of the battery. TESTING OPERATION OF THE KIT 1. Lower the golf cart if it was raised and test your new LEDGlow Million Color LED Golf Cart Underbody Kit. Cycle through the colors and modes to ensure full functionality by pressing the buttons on the control box or by using one of the included remotes. 2. With the golf cart on the ground, turn the steering wheel as far as it can go in both directions to ensure that there will be no tubes and/or wires coming in contact with the tires. If a tube or wire is damaged, the warranty will be voided. SECTION 2: PAIRING THE KIT TO YOUR DEVICE Apple Device Pairing Instructions (iOS 9.1 & Up Required): 1. Open the iOS App Store. 2. Search the iOS App Store for “LEDGlow Golf Cart Control” by typing it into the search bar. 3. Download the LEDGlow Golf Cart Control App and install it on your iOS device. 4. Open the LEDGlow Golf Cart Control App. 5. Power the control box using a 12 volt source. If the LED status indicator light on the control box is yellow, it is ready to be paired with the LEDGlow Golf Cart Control App. The status indicator light on the control box will turn green when the control box is finished pairing. 6. If the LED status indicator light is red, disconnect power from the control box, then reconnect power. When power is reconnected, the LED status indicator light will turn yellow, indicating the control box is ready to be paired to the app. The status indicator light will turn green when it is finished pairing with the app. LEDGlow Golf Cart Control App:
10 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com Android Device Pairing Instructions (Android 4.4 & Up Required): 1. Open the Google Play Store. 2. Type in “LEDGlow Golf Cart Control” into the Google Play Store search bar. 3. Download and install the LEDGlow Golf Cart Control App. 4. Confirm location services are enabled if you are using Android 4.4 or higher. To enable locations services, go to Phone Settings > Location > On. Restart the app if location services were disabled after installing the LEDGlow Golf Cart Control App. 5. Power the control box using a 12 volt source. If the LED status indicator light on the control box is yellow, it is ready to be paired with the LEDGlow Golf Cart Control App. The status indicator light on the control box will turn green when the control box is finished pairing. 6. Open the LEDGlow Golf Cart Control App. 7. If the LED status indicator light is red, disconnect power from the control box, then reconnect power. When power is reconnected, the LED status indicator light will turn yellow, indicating the control box is ready to be paired to the app. The status indicator light will turn green when it is finished pairing with the app. SECTION 9: OPTIONAL AUXILIARY SWITCH COURTESY LIGHT FEATURE WIRING INSTRUCTIONS: 1. The Auxiliary Switch Courtesy Light Feature will automatically change all installed lights to a pre-set color, illuminating the ground around the vehicle when the switch is activated. To utilize the optional courtesy lights feature, connect the white wire from the control box and connect to the load side of the auxiliary switch. Be sure that there is only 12 volts on the line side of the auxiliary switch. 2. Please note, some switches can be ground-side controlled. If this is the case, set the courtesy switch type to GND on the settings page of the LEDGlow Golf Cart Control App. 3. By default, the Courtesy Light Feature is turned off in the LEDGlow Golf Cart Control App. Make sure to turn it on in the app’s settings page after completing the wiring steps above. 4. In order to select your optional courtesy light color, open the settings page of the LEDGlow Golf Cart Control App and toggle the Courtesy Light button to on and there will be 7 color options that show up. Please select the color that you would like to use for this feature. If you would like to change your selection toggle the Courtesy Light button off and then on again and the 7 color selection will reappear. SECTION 10: OPTIONAL DISPLAY MODULE FEATURES & INSTALLATION The Display Module serves as a physical representation of how the installed underbody kit, along with any installed add-on kits, will appear on your vehicle. The Display Module mimics all LEDGlow Golf Cart Control App:
11 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com settings from the Golf Cart Control App and replicates them via embedded LEDs throughout the surface of the Module. Replicated settings include color, patterns, and where those lights are illuminated on the vehicle. The Display Module utilizes embedded LEDs within nine specific areas to indicate light color and patterns set to the Underbody, Wheel Well, and Interior/Canopy tubes. The top of the display represents the passenger side of the vehicle, while the bottom represents the driver’s side. The vertical sections at the far left and right represent the front and rear underbody tubes on the vehicle. The corners represent the wheel well tubes. The center of the Display Module features the LEDGlow logo and four buttons which control features and settings of the kit. However, when these buttons and the logo are illuminated, they also represent the color and pattern set to an installed interior kit. Wheel Wells Music Sensor DRIVER SIDE PASSENGER SIDE VEHICLE FRONT VEHICLE REAR Ambient Light Sensor The four buttons on the Display Module are fully operational and are used to adjust the light kit’s settings. Detail on the function of each button can be found below: Power Button: Pressing this button will turn the kit on or off. Pressing and holding this button will turn the lights on the Display Module on or off, but the light kit will remain on. Speed Change Button: Selects different speeds for selected patterns. Changing Color Button: Selects from 7 solid colors: blue, green, teal, red, pink, yellow, and white. Pressing and holding this button will scroll through a million color fade but will stop when the button is released. Mode Button: Changes the current mode displayed. There are 16 distinct modes. Each press of the Mode Button will advance to the next mode. A complete list of modes can be found on page 12. Pressing and holding this button will turn music mode on or off.
12 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com In addition to the display buttons, there is a music mode that will allow the lights to react to the sound of your stereo. When in music mode, the LEDGlow logo on the Display Module will be illuminated in red, regardless of the color set to the interior kit in the vehicle. The buttons on the Display Module, however, will be illuminated to reflect the specific settings applied to the interior tubes despite the activation of music mode. The Display Module features an ambient light sensor to control brightness. There is an autodimming feature built into the Display which automatically adjusts the brightness of the embedded lights according to its surrounding light. On a bright day, the Display Module will adjust itself by increasing its brightness for better visibility. At nighttime or in a dark setting, the Display Module will automatically dim itself. The Display Module was designed to offer multiple mounting capabilities on the interior of your vehicle. Due to its wire location, which exits from the back, the Module can easily be flush mounted on any flat surface. Additionally, there is a knock-out tab located on the bottom of the Display where the attached wire can exit. Positioning the wire in this way allows the Display to be surface mounted to the location of your choice. Please note, once the knock-out tab is removed, it cannot be replaced. To surface mount the Display Module, simply identify a mounting location, clean the location thoroughly with an alcohol prep pad, and mount the Display Module with 3M™ tape. Be sure to secure the power wire and keep it clear of the pedals and other moving parts within the vehicle. Route the wire through the firewall with a grommet in place and plug it into the port on the installed control box labeled “DISPLAY.”
13 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com SECTION 11: APP FEATURES & FUNCTIONALITY If you haven’t done so already, download the LEDGlow Golf Cart Control App and pair your device following the steps on page 9-10. 1. Underbody Tab: Changes the colors and modes for the underbody lights. 2. Wheel Tab: Changes the colors and modes for the wheel well lights when unlinked. 3. Interior/Canopy Tab: Changes the colors and modes for the interior lights when unlinked. 4. Settings Tab: Displays setting options within the app. 5. Power Toggle Option (For Linked Kits): Turns all of the selected kit components either on or off. 6. Link/Unlink: While linked, the system can run as one unit and all features will function together across all components. When unlinked, each kit component can be independently controlled. When the link icon is highlighted, components are linked together. When the icon is greyed out, components are not linked together. 7. Color Bar: Previews the selected colors assigned to each tab. 8. Color Wheel: Use the wheel to select the colors you’d like to assign to each installed component. Up to 3 colors can be assigned to each component at one time. 9. Brightness: Adjusts the brightness of a selected color. 10. Million Color: When set to “On” the kit will automatically scroll through every color variation available. 11. Fade: Applies a fade effect to any active mode. The fade feature can also be applied when two or more colors are selected from the color wheel, with or without a mode. 12. Speed Bar: Adjusts each mode’s rate of speed by decreasing or accelerating movement. 16 15 14 13 12 11 10 9 7 8 5 6 1 2 3 4 13. Strobe: Applies a strobe effect to any active mode. 14. Mode: Provides a drop down of 16 unique modes. See page 16 for a full list of modes and descriptions of each. 15. Music Mode: Reacts to the sound of your stereo if the optional Display Module is installed. With the Display Module installed, simply toggle the music mode to “ON” to activate this feature. 16. Preset: Provides 5 programmable and customizable preset modes.
14 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com SECTION 12: APP SETTINGS 1. System Power: Turns the entire kit on and off. 2. Courtesy Light: Powers on the courtesy light option. 3. Courtesy Light Color Selection: Allows you to select the color of all the lights when the white courtesy wire is triggered. Cycle the courtesy light Off/On switch to have the color options appear, once selected the color options disappear. Cycle the courtesy light Off/On switch to have the color options reappear. 4. Courtesy Switch Type: Changes the signal output from the control box to the connection point of the white wire to be either a 12 volt positive source or a ground source to activate the courtesy light function. (Refer to page # for wiring instructions.) 5. Display Wheel Tab: Allows you to hide the wheel tab if the optional wheel well kit was not installed. 6. Display Interior/Canopy Tab: Allows you to hide the interior tab if the optional interior kit was not installed. 7. Low Voltage Shut Off: Cuts the power to the kit if the vehicle’s battery voltage drops under 11 volts for two minutes. 8. Auto Dim Display: Enables/Disables the Display Module’s auto-dimming feature 9. Display Brightness: Controls the brightness level of the display module. This is only available if the Display Module is plugged into the control box. 10. Help: Takes you to LEDGlow’s Online Support Portal. 11. Display Connected: Unlocks music mode capabilities included with the display module. If the Display is not connected, the music features are hidden and a “NO” indicator will appear. To activate music mode, connect the Display Module to the control box and toggle music mode to “ON” in the component tab for the part or part(s) of the light kit to which you would like to assign the music mode feature. 12. Reset Settings: Resets all settings back to default. 10 11 12 1 2 3 4 5 6 7 8 9
15 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com SECTION 13: HOW TO USE THE APP How to Add a Single Color: Tap on the color bar until it expands into the color wheel. Select the desired color in the expanded color wheel and tap it to create a programmed color. Note: Be sure only one color is selected for solid illumination. How to Add a Second or Third Color: On the right side of the color wheel there are three white outlined circles. Tap each of the three circles and select a color from the color wheel. How to Remove a Second or Third Color: Expand the color wheel by tapping on the color bar if the color wheel is not already expanded. For Android users, press and hold the desired color to be removed. For iOS users, select the color you want to eliminate by pressing and holding for 2 seconds. Press the “X” to complete. How to Link/Unlink the Wheel Well or Interior Components: Different components of the kit can be operated together or independently of each other. Linking components together will allow the same colors and patterns to be used across them. Unlinking components will allow each of them to be controlled independently. Locate the link icon on the main underbody tab, or by tapping on either the “WHEEL” or “INTERIOR/CANOPY” tabs. Tap the link icon ( ) once to unlink the selected section. Tap the link icon again to link them together. How to Turn on the Million Color Mode: Million Color Mode cycles through all available colors. To turn it on or off, tap on the color bar to expand the color wheel. Use the toggle option to turn the Million Color Mode either on or off. Program the Million Color Mode on a selected component or assign this mode to all available components. How to Turn on the Fade Mode: Expand the color wheel by tapping on the color bar. After the color wheel is expanded, utilize the available toggle option to turn the fade mode on or off for integrating a fading transition to selected kit areas. How to Change the Speed on a Mode: Program more than one color on the app and slide the speed bar to adjust the color transition and/or mode. How to Turn on the Strobe Mode: Locate the strobe toggle located above the mode bar near the bottom of the app screen. Slide the white circle on the strobe bar to on or off to integrate a white strobing effect into any mode. How to Change the Brightness: Check the app screen to verify that the color wheel is expanded. Tapping the color bar will expand the color wheel if needed. Locate the brightness bar under the color wheel. Use the slider to decrease or increase color brightness. How to Change a Mode: Scroll to the bottom of the page and tap on “mode.” Tap on the list to select a mode. How to Turn on the Courtesy Lights: Press the settings tab ( ). Find the Courtesy Light Feature section and set it to “on” by sliding the toggle. How to Change 12V or GND for Courtesy Lights: Press the settings tab ( ). Once in settings, you will see the option to toggle between 12V and GND. If your Golf Cart has a ground side controlled system with constant power to the accessory switch, have the courtesy switch type
16 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com set to GND. If your Golf Cart accessory switch circuit is controlled by power and the ground never changes, have the courtesy switch type set to 12V. See page 14 for more details. How to Hide the Wheel Well Tab: Press the settings tab ( ) and toggle the wheel well tab to “off.” How to Hide the Interior/Canopy Tab: Press the settings tab ( ) and toggle the interior tab to “off.” How to Save a Preset: Determine the mode and color choices desired to save as a preset. For Android users, press and hold down for 2 seconds on the selected preset number, which will prompt a confirmation message on the screen indicating that the preset has been saved. For iOS users, press and hold down on the desired preset number to save and press “OK” after the popup notification appears. How to Reset the App: Go to the settings tab ( ) and tap on “Reset Settings.” This will reset all settings back to default. SECTION 14: FUNCTIONALITY The names, order, and descriptions of the modes are: Solid: Sets the kit to a solid color chosen from the color wheel. If more than one color is selected, the color will switch instantly to the next. Pulse: Gradually fades the light then flashes back on in a pulse effect. Sweeping: Lights up the entire front of the kit and gradually runs down the sides until reaching the rear in a sweeping motion. Kitt Scanner: Creates a scanning motion beginning at the center of the front of the kit that extends to the sides and ends at the center of the rear. Karr Scanner: Similar to Kitt Scanner, but creates a scanning motion that begins simultaneously at the center of the front and rear tubes. The light then moves from both ends of the vehicle to the opposite ends of the vehicle, passing through each other halfway down the sides, ending at the center of the opposite ends of the vehicle. Chase: Gradually lights up the entire front section of the kit, then trickles down the sides until reaching the rear tube in a chase pattern. Color Chase: Creates a chasing effect that starts in the front of the kit, reaches the rear, and then meets back again in the center of the sides. This mode works best with two or more colors selected. Chase vs Chase: Creates a chasing effect from both the front and rear, crossing each other in the center of the sides. This mode works best with two or more colors selected. Progression: Lights up the front entirely along with select parts of the sides as they scan front to back until reaching the rear. Running Color: Creates a scanning color effect on top of a solid color.
17 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com Flash: Flashes all lights simultaneously. Wig Wag: Lights up the front and rear simultaneously. After the front and rear illuminate, both of the sides light up simultaneously. Solid Zone: Flashes solid sections of the front and back while the sides flash simultaneously. Section Pulse: Creates a pulse effect that cycles through the kit. Light Show: Creates a scanning effect that cycles through the kit and then stops and flashes. Once it is finished flashing, it begins scanning again. Equalizer: Starting at the center of the front tube, solid light radiates outward, extending to the side tubes, then to the rear tube, illuminating the rear tube from the outside ends to the center, eventually lighting all of the tubes simultaneously. The pattern then moves back to the front of the vehicle in reverse, shutting off the lights as it radiates back to the center of the front tube. SECTION 15: TIPS & TROUBLESHOOTING The LEDGlow Golf Cart Control App will not disconnect while multitasking between other apps or phone features. Force-closing the app will not automatically shut down the kit. Shut down the app by double-tapping your mobile device’s “back” button when utilizing the app. Pairing will automatically occur after the initial app setup, as long as Bluetooth is turned on in the iOS or Android app settings and the controller is fully powered. If the Android or iOS device cannot connect to the controller, try one of the following steps and then reopen the LEDGlow Golf Cart Control App: Restart or select the power cycle option on any Android or iOS device. Restart your Bluetooth-enabled control box by disconnecting its power for 20 seconds, reconnect power, and test the kit for proper functionality.
18 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER LEDGlow Lighting, LLC (“LEDGlow”) warrants to the original retail consumer purchaser, and not any other purchaser or subsequent owner, that this Product will be free from defects in material or workmanship for a period of one (1) year from the purchase date. This warranty does not cover any Product that is (1) installed incorrectly, or (2) damaged by collisions, vandalism, other accidents, or similar causes. For a period of one (1) year from the date of purchase, at no charge to the Purchaser, LEDGlow will repair or replace this Product if it is determined by LEDGlow to be defective. After the warranty period, the Purchaser must pay all charges for parts and labor. Coverage under this warranty is only valid within the United States, including its territories, as well as in certain other countries. Purchasers should check our website, www.LEDGlow.com, to determine the warranty coverage in the countries in which they are located. LEDGlow does not warrant the installation of the Product, which is the sole responsibility of the Purchaser. Installation should be done by licensed professionals. Improper installation may cause damage to the Product and any vehicle in which it is installed, and may cause burns and electrical injury to individuals. LEDGlow’s warranty does not cover any expenses incurred in removing Products that are defective or re-installing replacement Products in their place. During the warranty period, to have the Product repaired or replaced, the Purchaser must return the Product, freight prepaid by the Purchaser, to LEDGlow (but for customers in the contiguous United States, LEDGlow will pay the shipping charges if any Product fails during the first thirty (30) days after purchase). The Product must be returned in its original carton or in a similar package affording an equal degree of protection. LEDGlow will return the repaired or replaced Product, freight prepaid, to the Purchaser. LEDGlow does not provide Purchasers with temporary replacement units during the warranty period or at any other time. This limited warranty is non-transferrable and will automatically terminate if the original retail consumer purchaser resells the Product or transfers the vehicle on which the Product is installed. An “original retail consumer purchaser” is a person who originally purchases the Product, or a gift recipient of a new Product that is in its original packaging and unopened. This limited warranty is subject to all of the following terms and conditions: TERMS AND CONDITIONS 1. NOTIFICATION OF CLAIMS; WARRANTY SERVICE: If Purchaser believes that a Product is defective in material or workmanship, written notice with an explanation of the claim shall be given promptly by Purchaser to LEDGlow. All warranty claims must be made within the warranty period, and any Products returned to LEDGlow must be shipped in accordance with LEDGlow’s procedures (including use of RMA numbers supplied by LEDGlow after notification). The repair or replacement of any Product or part thereof shall not extend the original warranty period. The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part, or the remaining period of the Product warranty, whichever is greater. 2. EXCLUSIVE REMEDY; ACCEPTANCE: Purchaser’s exclusive remedy and LEDGlow’s sole obligation is to supply (or pay for) all labor necessary to repair any Product found to be defective within the warranty period and to supply new or rebuilt replacements for defective parts. LEDGlow will refund the purchase price for such Product only if repair or replacement fails to remedy the defect. Purchaser’s failure to make a claim as provided in paragraph 1 above or continued use of the Product shall constitute an unqualified acceptance of such Product and a waiver by Purchaser of all claims thereto.
19 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com 3. EXCEPTIONS TO LIMITED WARRANTY: LEDGlow shall have no obligation to Purchaser with respect to any Product that is subjected to any of the following: abuse, improper use, negligence, accident, modification, failure to follow the operating procedures outlined in the user’s manual, failure to follow the maintenance procedures in the service manual for the Product, attempted repair by non-qualified personnel, operation of the Product outside of the published environmental and electrical parameters, or if the Product’s original identification (trademark, serial number) markings have been defaced, altered, or removed. LEDGlow excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS. LEDGlow also excludes from warranty coverage any consumable items such as fuses and batteries. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. 4. PROOF OF PURCHASE; REGISTRATION: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility. Registration of any Product or of this limited warranty is voluntary, and failure to register will not diminish any rights available under this warranty. DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES, LEDGLOW HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE OR IN ANY OTHER STATE STATUTE. LIMITATION OF LIABILITY THE LIABILITY OF LEDGLOW, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT FOR WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL LEDGLOW BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER. GOVERNING LAW: This non-transferrable limited warranty shall be governed by the law of the State of New Jersey, U.S.A., and the United States of America, excluding their conflicts of laws principles. The courts of Camden County, New Jersey, shall have the exclusive jurisdiction over any legal action with respect to this warranty. This limited warranty gives specific legal rights. You may also have other rights that may vary from state to state or from country to country. Some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. You are advised to consult applicable state or country laws for a full determination of rights.
20 INSTALLATION GUIDE Tech Support 856-768-5700 Ext. 2 • TechSupport@LEDGlow.com LEDGlow Lighting, LLC • LEDGlow.com LEDGLOW LIGHTING, LLC • 1.877.LED.GLOW • LEDGLOW.COM 444 COMMERCE LANE SUITE B, WEST BERLIN, NJ 08091 06/24 LIFETIME TECHNICAL SUPPORT 1 YEAR LIMITED WARRANTY
RkJQdWJsaXNoZXIy MTIxODAy